Hi,
I have a question about the hyperthreading. Previously when I wanted to allocate full node with hyperthreading I did this:
#SBATCH --nodes=1 #SBATCH --cpus-per-task=1 #SBATCH --ntasks-per-core=2 #SBATCH --ntasks-per-node=96 #SBATCH --mem=180G
This no longer works, i.e., setting ntasks per node to anything higher than 48 will show sbatch: error: Batch job submission failed: Requested node configuration is not available even when the --ntasks-per-core=2 is set. Any ideas? How can I allocate full node with hyperthreading?
Best regards Pavel Ondračka
Hi Pavel,
due to scheduling issues, which led to not understandable errors, we disabled hyperthreading.
Best Marcus Am 07.03.2019 um 09:06 schrieb Pavel Ondračka:
Hi,
I have a question about the hyperthreading. Previously when I wanted to allocate full node with hyperthreading I did this:
#SBATCH --nodes=1 #SBATCH --cpus-per-task=1 #SBATCH --ntasks-per-core=2 #SBATCH --ntasks-per-node=96 #SBATCH --mem=180G
This no longer works, i.e., setting ntasks per node to anything higher than 48 will show sbatch: error: Batch job submission failed: Requested node configuration is not available even when the --ntasks-per-core=2 is set. Any ideas? How can I allocate full node with hyperthreading?
Best regards Pavel Ondračka _______________________________________________ claix18-slurm-pilot mailing list -- claix18-slurm-pilot@lists.rwth-aachen.de To unsubscribe send an email to claix18-slurm-pilot-leave@lists.rwth-aachen.de
Hi Pavel,
HT was deactivated yesterday. So there are only 48 tasks left
Best regards, Dieter
-----Original Message----- From: Pavel Ondračka ondracka@mch.rwth-aachen.de Sent: Thursday, March 7, 2019 9:06 AM To: claix18-slurm-pilot@lists.rwth-aachen.de Subject: [claix18-slurm-pilot] disabled hyperthreading?
Hi,
I have a question about the hyperthreading. Previously when I wanted to allocate full node with hyperthreading I did this:
#SBATCH --nodes=1 #SBATCH --cpus-per-task=1 #SBATCH --ntasks-per-core=2 #SBATCH --ntasks-per-node=96 #SBATCH --mem=180G
This no longer works, i.e., setting ntasks per node to anything higher than 48 will show sbatch: error: Batch job submission failed: Requested node configuration is not available even when the --ntasks-per-core=2 is set. Any ideas? How can I allocate full node with hyperthreading?
Best regards Pavel Ondračka _______________________________________________ claix18-slurm-pilot mailing list -- claix18-slurm-pilot@lists.rwth-aachen.de To unsubscribe send an email to claix18-slurm-pilot-leave@lists.rwth-aachen.de
OK,
BTW is there some mailing list where should I subscribe to be aware of such changes in the future?
Best regards
Pavel
________________________________ From: an Mey, Dieter Sent: Thursday, March 7, 2019 2:36:37 PM To: Ondracka, Pavel; claix18-slurm-pilot@lists.rwth-aachen.de Subject: RE: [claix18-slurm-pilot] disabled hyperthreading?
Hi Pavel,
HT was deactivated yesterday. So there are only 48 tasks left
Best regards, Dieter
-----Original Message----- From: Pavel Ondračka ondracka@mch.rwth-aachen.de Sent: Thursday, March 7, 2019 9:06 AM To: claix18-slurm-pilot@lists.rwth-aachen.de Subject: [claix18-slurm-pilot] disabled hyperthreading?
Hi,
I have a question about the hyperthreading. Previously when I wanted to allocate full node with hyperthreading I did this:
#SBATCH --nodes=1 #SBATCH --cpus-per-task=1 #SBATCH --ntasks-per-core=2 #SBATCH --ntasks-per-node=96 #SBATCH --mem=180G
This no longer works, i.e., setting ntasks per node to anything higher than 48 will show sbatch: error: Batch job submission failed: Requested node configuration is not available even when the --ntasks-per-core=2 is set. Any ideas? How can I allocate full node with hyperthreading?
Best regards Pavel Ondračka _______________________________________________ claix18-slurm-pilot mailing list -- claix18-slurm-pilot@lists.rwth-aachen.de To unsubscribe send an email to claix18-slurm-pilot-leave@lists.rwth-aachen.de
claix18-slurm-pilot@lists.rwth-aachen.de